If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

A question about G.W.R. engines

Discussion in 'Steam Traction' started by 240P15, Dec 11, 2017.

  1. Masterbrew

    Masterbrew New Member

    Joined:
    Feb 3, 2016
    Messages:
    90
    Likes Received:
    55
    Gender:
    Male
    Location:
    Staplehurst, Kent
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    The FR loops used to have a "through road" (the straightest route) and a loop road. Uphill passenger trains had priority for the through road over down trains but down passenger trains had priority over other trains. Minfford, Tan-y-Bwlch and Tan-y-Griseau are right-hand running whilst Penrhyn & Ddaullt (removed) and Rhiw Goch were/are left hand. Down trains used to take the main platform road (left side in direction of travel) at Minfford when not passing other trains but the points at the north-east end now give a straight run into the right-hand road.
     
  2. Railcar22

    Railcar22 Member

    Joined:
    Sep 5, 2007
    Messages:
    239
    Likes Received:
    30
    Gender:
    Male
    Occupation:
    Stock Control
    Location:
    Slough
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    It actually has nothing to do with Napoleon whatsoever. All of Europe up until about 1905, drove on the left hand side of the road, but some dum French idiot decided the they would drive on the right. And all of Europe folloed suit
     
    Spinner likes this.
  3. LesterBrown

    LesterBrown Member

    Joined:
    Jan 20, 2009
    Messages:
    995
    Likes Received:
    761
    Location:
    Devon
    Although the Americans have always driven on the right the Ford Model T was, apparently, the first car there to have the steering wheel on the left hand side rather than on the right.
     
  4. bob.meanley

    bob.meanley Member

    Joined:
    Apr 19, 2010
    Messages:
    255
    Likes Received:
    770
    Which demonstrates that those on the design panel were forced to agree the superiority of Great Western boiler mountings, why else would they logically choose them? They even got to be fitted to diesel train heating boilers, which ensured a supply of such fittings to early preservation projects, many with cocks having Klinger packing sleeves which are keenly sought to this day.
    Bob
     
    Martin Perry likes this.
  5. bob.meanley

    bob.meanley Member

    Joined:
    Apr 19, 2010
    Messages:
    255
    Likes Received:
    770
    Not entirely true. The official reason given for removal of vacuum pumps on the relative ERO Job number was that they were suspected of causing the fracture of piston rods adjacent to the crosshead, first and foremost a serious technical issue, but conceded that it would have had a cost. The GWR incidentally did not, and still does not, seem to experience similar problems with piston rod fractures.Now in the Great Western application the pump was connected to the brake system via the Vacuum Retaining (VR) valve. This system was quite sophisticated and the VR valve caused the pump to be turned over to evacuating the reservoir side of the brake when an application was made which caused a fall in train pipe vacuum. In the LMS application there was no reservoir and no VR valve, so when an application was made, it required judicious use of the brake valve to overcome the pump trying to carry on evacuating the train pipe, a bit like trying to put the brake on with the large ejector open. Now this problem was magnified considerably when two Stanier engines were double heading and several instances occurred where such doule headed trains passed signals at danger due to an ability to make a sufficient reduction of train pipe vacuum to make a satisfactory stop, and it is believed that this was one of the main contributory factors in the deletion of pumps, but hardly one which could politically be declared.
    Regards
    Bob
     
  6. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    This is all true, of course, Bob. But the GWR system certainly was effective, no doubt, but also quite complex, and I struggle to see how such a system which involved a number of moving - and wearing - parts was cheaper to maintain than an ejector, with NO moving parts!
     
  7. bob.meanley

    bob.meanley Member

    Joined:
    Apr 19, 2010
    Messages:
    255
    Likes Received:
    770
    You have obviously never had the pleasure of maintaining a GW system. Like all Great Western fittings, the kit lasts for ages and ages and it is very unusual for it to give problems. Major ones are sliding bands ion cylinders and cylinder glands which require occasional re-packing. Brake valves jsut go on and on and need little attemntion as do steam ejector steam valve seats. I c annot remember us ever having to recut a steam valve seat for the last twenty years on 4965 or 5043. If you have ever experienced the maintenance of an LMS standard steam brake valve you might notice a difference. Pipework is substantial and normally gives little trouble, as you would expect from a system working at a higher vacuum - leakage is not a desirable item. The maintenance claims are pretty well true in my experience.
     
  8. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I concede the point!

    Although I volunteer as a fitter at Bridgnorth, most of my experience, although by no means all, is on LMS types. My user name is a bit of a clue!
     
    Last edited: Dec 18, 2017
  9. andrewshimmin

    andrewshimmin Well-Known Member

    Joined:
    Mar 18, 2011
    Messages:
    1,761
    Likes Received:
    2,160
    Heritage Railway Volunteer:
    No I do not currently volunteer
    However, we must also concede that the LMS, a commercial company, had hundreds of each type in service, and found that the GWR one was, overall, more expensive. And they kept very careful accounts...
    Perhaps there are issues of scale here - what is true on a fleet of a dozen or so locos lovingly maintained may be different to what happened in the hurly burly of 1930s service.
     
    Bluenosejohn likes this.
  10. threelinkdave

    threelinkdave Well-Known Member

    Joined:
    Aug 1, 2013
    Messages:
    2,065
    Likes Received:
    1,240
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Stratford-upon-Avon or in a brake KD to BH
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    As regard to effectieness of brakes my main concern is not how powerfull they are but how long they last when applied. The guards nightmare is the divided train. 21in or 25in makes mot a lot of odds the two halves will stop' . What matters now is how long will the brakes remain effective. BR, SR, LNER AND LMS used rolling rings in their cylinders which provide a good seal and give a lasting application. The GWR use a wiping seal in their cylinders and these readily leak off. You can almost guarantee that a GW set left overnight will suffer from most of the brakes leaking off. Conversely where a rolling ring is used most brakes will still be applied the next morning

    If I did suffer a split train I would rather deal with a 21in system which remained effective whilst looking to recouple the train than a more powerful 25in system which leaked off in 30 minutes
     
    Bluenosejohn, Johnb and Forestpines like this.
  11. Railcar22

    Railcar22 Member

    Joined:
    Sep 5, 2007
    Messages:
    239
    Likes Received:
    30
    Gender:
    Male
    Occupation:
    Stock Control
    Location:
    Slough
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    When our Hawkesworth Brake Third 2202 went to Bold in 1980 with 5051, she was left standing for 1 day with vac brakes on, they had to be blown down to move the coach. And when on vintage train railtours, the BR drivers would use loco air brake only, to slow the train down, as if they used the vac brakes, the train would stop too early, as the brakes were so effective, compared to BR vac brake trains
     
  12. threelinkdave

    threelinkdave Well-Known Member

    Joined:
    Aug 1, 2013
    Messages:
    2,065
    Likes Received:
    1,240
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Stratford-upon-Avon or in a brake KD to BH
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I have no doubt some GWR cylinders wont leak off. At the SVR we have a good mix of LNER, LMS, BR AND GWR passenger stock. Part of train prep is to pull the strings to destroy captive vacuum to ensure nothing is left at 25in. I know its subjective but experience has shown that more GWR coaches will have leaked off than the others
     
  13. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    My experience is similar.
     
  14. bob.meanley

    bob.meanley Member

    Joined:
    Apr 19, 2010
    Messages:
    255
    Likes Received:
    770
    If sliding band cylinders are properly maintained and fitted with bands of the correct design and grade of material there should be no such problems with them. Do bear in mind that this design was also used by BR and such performance would not have been tolerated by the GWR or for that matter the HMRI. Quiet simply if you have a set which will not stand overnight without leaking off, or which gives the slightest concern about such issues should it divide in trafic, the set should clearly not be in traffic until your maintenance department done something about it, and given the audience which this website garners from various organisations, this is a pretty foolhardy statement to make in public. The very next time that you come across vehicles whose vac brake has leaked off overnight, I suggest that you book them rather than expounding theories such as this.
    Regards
    Bob
     
  15. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I'm not sure that leaking off overnight is a major issue; I suspect much air braked stock would do the same. But if a coach cannot maintain sufficient vacuum to bring a break-away to a stand, that's a different matter.
     
  16. Wenlock

    Wenlock Well-Known Member Friend

    Joined:
    Oct 26, 2008
    Messages:
    2,027
    Likes Received:
    1,319
    Gender:
    Male
    Occupation:
    Bus Driver
    Location:
    Loughton Essex
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I know the vacuum should stay on for a while, but I was taught to never rely on it staying on long term. When I worked in a freight yard, there was an expectation that anything left for a day or two would leak off.
    Once a rake of about 20 presflos were kept in the yard on a Friday night, next service Monday p.m. a shunter on Monday morning pushed a long rake in onto them expecting some resistance to get 700 tons moving. He didn't expect them to stand rock solid with the brakes still hard in, resulting in the first half dozen wagons on his shunt to jump up then land in the dirt.
     
  17. threelinkdave

    threelinkdave Well-Known Member

    Joined:
    Aug 1, 2013
    Messages:
    2,065
    Likes Received:
    1,240
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Stratford-upon-Avon or in a brake KD to BH
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I have tried to ascertain a standard for leakage rates for vac cylinders. I have been plowing through Railway Group Standards and could only disover a standard which required a drop of less than 2in in 5 minutes. Taking this to its mathematical conclusion20inches will drop in 50 minutes. There appears no standard which requires a vac cylinder to remain on overnight. If someone can show me such a standard I will eat humble pie.

    Berthed trains are required to be secured by handbrakes or adequate scotches. The automatic brake, air or vac, must not be relied on. In the case of the Great Central runaway the RAIB highlights the failure of the scotch and non use of the loco handbrake. That the loco air brake failed is mentioned in passing but appears not to be central to the report (R042015_150521_Loughborough_Central
     
    andrewshimmin, LMS2968 and Wenlock like this.
  18. jtx

    jtx Well-Known Member

    Joined:
    Jul 4, 2007
    Messages:
    1,868
    Likes Received:
    855
    Gender:
    Male
    Occupation:
    Happily retired
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Can't speak for Apple, but, smiley or not, your comments re GWR locomotives are complete cobblers, speaking from 40 years experience.
     
  19. K14

    K14 Member

    Joined:
    Nov 6, 2011
    Messages:
    403
    Likes Received:
    298
    Location:
    Catford
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Correct. For coaching stock:—

    BR 10906 - (1969) - 2" in 5 minutes;
    CMS 123 - (1988) - 4" in 5 mins;
    CEPS 1019 - (1990) - 1/2" in 15mins

    CMS 123 is widely touted as the standard to meet.

    Pete S.,
    C&W Dept.,
    GWS Didcot
     
    threelinkdave and andrewshimmin like this.
  20. 240P15

    240P15 Well-Known Member

    Joined:
    Dec 1, 2017
    Messages:
    1,598
    Likes Received:
    1,588
    Gender:
    Male
    Location:
    Norway
    Heritage Railway Volunteer:
    No I do not currently volunteer

    If I have understood this correct a Left Hand Driving locomotive the driver will be standing at the right side at the footplate?
     

Share This Page