If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

Elastic Spike Extractor - experiences?

Discussion in 'Civil Engineering M.I.C.' started by Sheff, May 17, 2018.

  1. Sheff

    Sheff Resident of Nat Pres

    Joined:
    Apr 21, 2006
    Messages:
    7,568
    Likes Received:
    2,345
    Gender:
    Male
    Occupation:
    Retired Engineer & Heritage Volunteer
    Location:
    N Warks
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    We don't use 'macbeth' spikes. Our are the inverted 'J' variety.
     
  2. Sheff

    Sheff Resident of Nat Pres

    Joined:
    Apr 21, 2006
    Messages:
    7,568
    Likes Received:
    2,345
    Gender:
    Male
    Occupation:
    Retired Engineer & Heritage Volunteer
    Location:
    N Warks
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Most of what you describe we have now already learnt the hard way ;) One thing I'm looking into is a way of fettling the plates to remove the rust and crud from the holes before attempting to hammer the spikes back in after changing the sleeper. A 3/4 in broach is looking favourite at the moment unless anyone has a better (tried and tested) method.
     
  3. Ploughman

    Ploughman Part of the furniture

    Joined:
    Apr 1, 2008
    Messages:
    5,806
    Likes Received:
    2,649
    Occupation:
    Ex a lot of things.
    Location:
    Near where the 3 Ridings meet
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    As has been said a couple of times, don't do it, scrap them and put in pan baseplates.
    I know the answer is money but after a few years in the track you will not be able to Tamp them with the spikes loosing grip.

    There was a conversion kit to enable an AS screw with springs and a steel plate to be inserted in one hole with a spike in another.
    Not sure what it is called as we got rid of all spikes years ago and not needed to know about them now.
    Just checked in a maintenance manual an LC - low cost clip was developed but not sure if it is available anywhere.
     
  4. Chris86

    Chris86 Well-Known Member

    Joined:
    Oct 31, 2011
    Messages:
    1,328
    Likes Received:
    1,315
    Occupation:
    Safety, Technical and Offroad Driver Trainer
    Location:
    South Yorkshore
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Would it be possible to use a Hi-lift farm jack with an adaptor to remove the spikes?

    Have used them for lifting/moving some fairly big bits of machinery and trees in the past- also as a winch?

    Regards

    Chris
     
  5. Sheff

    Sheff Resident of Nat Pres

    Joined:
    Apr 21, 2006
    Messages:
    7,568
    Likes Received:
    2,345
    Gender:
    Male
    Occupation:
    Retired Engineer & Heritage Volunteer
    Location:
    N Warks
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Possibly but the correct tool exists and we have one.
     
  6. Sheff

    Sheff Resident of Nat Pres

    Joined:
    Apr 21, 2006
    Messages:
    7,568
    Likes Received:
    2,345
    Gender:
    Male
    Occupation:
    Retired Engineer & Heritage Volunteer
    Location:
    N Warks
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Yes that would be lovely but requires £££ we don’t have.
     
    stephen hornby likes this.
  7. stephen hornby

    stephen hornby New Member

    Joined:
    Oct 31, 2018
    Messages:
    6
    Likes Received:
    1
    Gender:
    Male
    Location:
    Jameson Road Fleetwood
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Hi, I ordered one of those steel wedges on Tuesday and it has arrived today. If all goes well I will try it on Saturday and let you know if it’s any good.
     
  8. stephen hornby

    stephen hornby New Member

    Joined:
    Oct 31, 2018
    Messages:
    6
    Likes Received:
    1
    Gender:
    Male
    Location:
    Jameson Road Fleetwood
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    We use the J spikes too at Jameson Rd. We’ve only just started to fettle the track so we haven’t got much money to throw about either!
     
  9. Sheff

    Sheff Resident of Nat Pres

    Joined:
    Apr 21, 2006
    Messages:
    7,568
    Likes Received:
    2,345
    Gender:
    Male
    Occupation:
    Retired Engineer & Heritage Volunteer
    Location:
    N Warks
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Yes we already have the wedges too - they come with the puller device and will free about 80% of the jammed spikes that the puller won't shift. The few that we can't get out we work around - either spin the plate out from under the rail, or pull the sleeper out and remove the plate after - all depends on how many seized spikes you have and in what combination.
     
  10. Ploughman

    Ploughman Part of the furniture

    Joined:
    Apr 1, 2008
    Messages:
    5,806
    Likes Received:
    2,649
    Occupation:
    Ex a lot of things.
    Location:
    Near where the 3 Ridings meet
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Page 32 of this booklet describes the clip.
    https://www.thepwi.org/technical_hu...eral_guides/creep_in_jointed_track_guide_2000
     
  11. Sheff

    Sheff Resident of Nat Pres

    Joined:
    Apr 21, 2006
    Messages:
    7,568
    Likes Received:
    2,345
    Gender:
    Male
    Occupation:
    Retired Engineer & Heritage Volunteer
    Location:
    N Warks
    Heritage Railway Volunteer:
    Yes I am an active volunteer
  12. stephen hornby

    stephen hornby New Member

    Joined:
    Oct 31, 2018
    Messages:
    6
    Likes Received:
    1
    Gender:
    Male
    Location:
    Jameson Road Fleetwood
    Heritage Railway Volunteer:
    Yes I am an active volunteer
  13. Martin Adalar

    Martin Adalar New Member

    Joined:
    May 2, 2018
    Messages:
    184
    Likes Received:
    64
    Gender:
    Male
    Location:
    5D
    Heritage Railway Volunteer:
    No I do not currently volunteer
    It is a false economy to fit scrap obsolete baseplates and elastic spikes to brand new sleepers, it sounds like your real problem is not being able to afford to maintain the track in the first place.
     
  14. NeilL

    NeilL Well-Known Member

    Joined:
    Mar 30, 2012
    Messages:
    1,916
    Likes Received:
    1,402
    Occupation:
    Retired & OAPWay & tree feller
    Location:
    Staffordshire
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    In an ideal world we would rip up the entire track and replace it with new rails and sleepers, however the cash available does to extend to that.

    In the real world we have to to do the best we can and the sleepers we are replacing have been in place for 50 years. If our work means it remains safely usable for another 20 years that sounds good to me.
     
    Sheff and stephen hornby like this.
  15. stephen hornby

    stephen hornby New Member

    Joined:
    Oct 31, 2018
    Messages:
    6
    Likes Received:
    1
    Gender:
    Male
    Location:
    Jameson Road Fleetwood
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    We have all got to start somewhere, after all BR seemed to think it was alright to run mainline locos on it in the past. I can't see the problem in using them if the base plates and pins are ok aswell as the sleepers being fit for purpose.
     
  16. Sheff

    Sheff Resident of Nat Pres

    Joined:
    Apr 21, 2006
    Messages:
    7,568
    Likes Received:
    2,345
    Gender:
    Male
    Occupation:
    Retired Engineer & Heritage Volunteer
    Location:
    N Warks
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Changing out life-expired sleepers IS maintaining track.
     
    stephen hornby likes this.
  17. Martin Adalar

    Martin Adalar New Member

    Joined:
    May 2, 2018
    Messages:
    184
    Likes Received:
    64
    Gender:
    Male
    Location:
    5D
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Quite so, but if you have to reuse that track fastening system you can buy brand new elastic spikes which are a low cost item and fit them in the old baseplates after cutting out the old ones if they are stuck or have lost their spring.
     
  18. sleepermonster

    sleepermonster Member

    Joined:
    Jun 19, 2007
    Messages:
    919
    Likes Received:
    1,024
    Hi Sheff,

    If you want a few spare BR1 plates come and see us at Wirksworth when you can. We've got lots, got anything to swap?

    Tim
     
  19. Sheff

    Sheff Resident of Nat Pres

    Joined:
    Apr 21, 2006
    Messages:
    7,568
    Likes Received:
    2,345
    Gender:
    Male
    Occupation:
    Retired Engineer & Heritage Volunteer
    Location:
    N Warks
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Hi Tim,

    Thanks, I’ll pass that on.

    What sort of stuff are you looking for?

    Hopefully be back on track next month, can’t remember the last time I was there!

    Sheff
     
  20. Sheff

    Sheff Resident of Nat Pres

    Joined:
    Apr 21, 2006
    Messages:
    7,568
    Likes Received:
    2,345
    Gender:
    Male
    Occupation:
    Retired Engineer & Heritage Volunteer
    Location:
    N Warks
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Hi Tim,

    We have a few BR1 in stock but we generally use the Pandrol clip type now. Thanks for the offer though.
     

Share This Page