If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

Plug valve overhaul

Discussion in 'Steam Traction' started by Barclay1181, Sep 1, 2014.

  1. Barclay1181

    Barclay1181 New Member

    Joined:
    Sep 17, 2012
    Messages:
    15
    Likes Received:
    0
    Has anyone had any experience overhauling bronze plug valves , the type typically used on blow downs etc. We have tried to overhaul 2 vavles, a 1/2" bore valve used as a whistle valve on AB # 1749 and the blow down valve fitted to Fowler #16342. The method we used was to machine the plug true then make an identical plug and wrapped fine sand paper to it and used this to true up the inside of the valve body. The 2 parts were then blued to check and reassembled. However they both leak ever so slightly so are not 100% tight. We would be interested to know any other ways of lapping these valves as information on there overhaul seems hard to come by.

    Any help gratefully received.

    Jason Durry
    Silver Stream Railway
    New Zealand
     
  2. 32110

    32110 Member

    Joined:
    May 20, 2006
    Messages:
    627
    Likes Received:
    726
    Gender:
    Male
    Occupation:
    Retired from full time paid work
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Could you post photos of the valve as I am not sure I understand your description.
     
  3. Martin Perry

    Martin Perry Nat Pres stalwart Staff Member Moderator Friend

    Joined:
    Apr 15, 2006
    Messages:
    16,510
    Likes Received:
    7,753
    Location:
    1012 / 60158
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Might be worth trying some very fine lapping paste rather than the sand paper.
     
  4. Eightpot

    Eightpot Resident of Nat Pres Friend

    Joined:
    Aug 10, 2006
    Messages:
    8,077
    Likes Received:
    2,264
    Gender:
    Male
    Occupation:
    Engineer Emeritus
    Location:
    Aylesbury
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I prefer something like pumice powder or the domestic 'Ajax' scouring powder for this sort of thing. Grinding/lapping compounds a bit too vicious for my liking. This assumes that the plug and body are a decent fit in the first place.
     
  5. Barclay1181

    Barclay1181 New Member

    Joined:
    Sep 17, 2012
    Messages:
    15
    Likes Received:
    0
  6. 32110

    32110 Member

    Joined:
    May 20, 2006
    Messages:
    627
    Likes Received:
    726
    Gender:
    Male
    Occupation:
    Retired from full time paid work
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    On AB 1719 I have a blowdown valve of this style. Assuming its not pitted and male and female parts are a good fit I have found that using grinding paste of various grades, finishing with fine gives acceptable results. I'm not saying that there might not be the odd drip from it. Tightness of the nut assists but can also make the valve very hard to operate. I do not use the valve as a blowdown when in steam but rather a method of draining the boiler.
     
  7. burnettsj

    burnettsj Member

    Joined:
    Mar 22, 2006
    Messages:
    208
    Likes Received:
    21
    Gender:
    Male
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Lapping with grinding paste is the way to go - just make sure you have the correct grade of paste.
     
  8. 32110

    32110 Member

    Joined:
    May 20, 2006
    Messages:
    627
    Likes Received:
    726
    Gender:
    Male
    Occupation:
    Retired from full time paid work
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Not heard from your project for quite a while. How are things progressing? You may have seen elsewhere that we have fitted AB1719 'Lady Nan' with new Gresham and Craven 5mm ones. Although they are the same injector size as the original AB ones they are physically much smaller. The big advantage is that they work well.
     
  9. jnc

    jnc Well-Known Member

    Joined:
    Apr 3, 2012
    Messages:
    1,511
    Likes Received:
    2,706
    Gender:
    Male
    Location:
    Western Atlantic
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Sandpaper's fine as the first step, to get a rough fit, but as others have said, you need to follow up with a series of finer and finer polishing pastes.

    Noel
     
  10. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Can you divulge the source of the injectors, assuming 'new' means new and not simply unused?
     
  11. Barclay1181

    Barclay1181 New Member

    Joined:
    Sep 17, 2012
    Messages:
    15
    Likes Received:
    0
    Things are progressing with 1181. It is a bit of a spare time project, gets pushed back when other railway projects take priority, currently have a carriage bogie undergoing a major overhaul so that's taking up a bit of time. We now have a new firebox on hand, made by Mendip Steam Restorations in Somerset. A fantastic job. The boiler is up on the newly fabricated trolleys, being cleaned down and assessed ready for repairs to start. I am aiming to have the repairs complete and hydro done by Feb 2019, in time for the boilers 80th birthday. Have done a few other bits and pieces, which can be viewed on the Facebook page, www.facebook.com/barclay1181restoration . If you are not a member of Facebook, you should still be able to see the pictures. What have you done with your old injectors? I could be interested in them if you have no further use for them?

    Regards
    Jason
     
  12. 32110

    32110 Member

    Joined:
    May 20, 2006
    Messages:
    627
    Likes Received:
    726
    Gender:
    Male
    Occupation:
    Retired from full time paid work
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    @Steve - I sourced the Gresham and Craven injectors from North Bay Railway Engineering Services ( http://www.nbres.co.uk/ ). I believe that 5mm is the largest that they do.
    @Barclay1181 - I still have the old worn out injectors. For the moment I am hanging on to them but at a later date I might be convinced otherwise.
    Photo showing the old and the new:

    P1070852a.JPG
     
    Wenlock likes this.
  13. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Thanks for the response I've had mixed reports about those figure 4 injectors from North Bay but it sounds like yours are OK.
     
  14. 32110

    32110 Member

    Joined:
    May 20, 2006
    Messages:
    627
    Likes Received:
    726
    Gender:
    Male
    Occupation:
    Retired from full time paid work
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    @Steve - I did have a problem with one of the body castings in that there was a flaw on the overflow boss that was only evident in use. It showed up as a fissure that went through the casting. As soon as this was pointed out to NBRES they did not hesitate to replace it with a sound unit.
     
  15. Nigel Day

    Nigel Day Member

    Joined:
    Mar 17, 2015
    Messages:
    270
    Likes Received:
    689
    Gender:
    Male
    Occupation:
    Steam loco engineer
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I tend to make a dummy plug for grinding in. Only on the final lapping of the actual valve plug do I use the finest grinding paste the followed by a metal polish like Peak or Brasso.
     
    Avonside1563 likes this.
  16. clinker

    clinker Member

    Joined:
    Oct 8, 2016
    Messages:
    569
    Likes Received:
    348
    Gender:
    Male
    Location:
    romford
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Traction enginemen seem to speak highly of 'Timesaver' lapping compound, which is available from places such as Heritage Steam Supplies, apparently, unlike other compounds, it doesn't require cleaning off after use. I'm told that grinding paste and similar needs cleaning off with nitric acid, but I've no actual experience of it.
     

Share This Page