If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

Stroke and Bore

Rasprava u 'Steam Traction' pokrenuta od SomeWeeb, 16. Svibanj 2022..

  1. SomeWeeb

    SomeWeeb New Member

    Pridružen(a):
    22. Rujan 2021.
    Poruka:
    31
    Lajkova:
    5
    Spol:
    Muškarac
    Grad:
    lyme NH
    Heritage Railway Volunteer:
    No I do not currently volunteer
    I'm doing a research project for my school but I have no idea how I'm meant to calculate stroke and bore. Could someone enlighten me?
     
  2. Flying Phil

    Flying Phil Part of the furniture

    Pridružen(a):
    10. Prosinac 2018.
    Poruka:
    3,018
    Lajkova:
    6,319
    Spol:
    Muškarac
    Grad:
    Leicestershire
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    For virtually all engines the dimensions for stroke and bore are available in reference books/on-line. The resultant of Stroke x bore x No of cylinders is also the cubic capacity of the engine. Usually used for ic engines though.
     
  3. Martin Perry

    Martin Perry Nat Pres stalwart Staff Member Moderator Friend

    Pridružen(a):
    15. Travanj 2006.
    Poruka:
    16,551
    Lajkova:
    7,897
    Grad:
    1012 / 60158
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Bore is simply the diameter of the cylinder.
    Stroke is the distance from the centre of the crankpin to the centreline of the axle/crankshaft.
    Both apply to steam or Diesel engines.
     
  4. Steve

    Steve Resident of Nat Pres Friend

    Pridružen(a):
    7. Listopad 2006.
    Poruka:
    12,729
    Lajkova:
    11,847
    Interesi:
    Gentleman of leisure, nowadays
    Grad:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
     
  5. Martin Perry

    Martin Perry Nat Pres stalwart Staff Member Moderator Friend

    Pridružen(a):
    15. Travanj 2006.
    Poruka:
    16,551
    Lajkova:
    7,897
    Grad:
    1012 / 60158
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    My bad … it’s been a long day!! :)
     
    LMS2968 se sviđa ovo.
  6. bantamd14

    bantamd14 New Member

    Pridružen(a):
    21. Siječanj 2017.
    Poruka:
    136
    Lajkova:
    92
    Spol:
    Muškarac
    Grad:
    Stafford
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Surely that only applies to i.c. locos and the few steam locos where the centre line of the cylinder is in line with the centre of the driven wheel?
    Most steam locos are not in-line and the initial horizontal motion is transferred through the crosshead, then rotary motion via the con rod. The cranked axle length is usually longer than half the piston stroke and the quartering of the wheel ensures that the other cylinder(s) complete the cycle (I think!). If it had one cylinder it would just oscillate, but that is the basic principle of a shaping machine (I am showing my age!).
    I think single cylinder locos like Rocket were in-line, but I don't know how they avoided getting stuck at T.D.C or B.D.C!
    I am open to other people's opinion, who will have greater knowledge than myself.
     
  7. Cosmo Bonsor

    Cosmo Bonsor Member

    Pridružen(a):
    10. Prosinac 2014.
    Poruka:
    221
    Lajkova:
    501
    Spol:
    Muškarac
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    [​IMG]
     
  8. LMS2968

    LMS2968 Part of the furniture

    Pridružen(a):
    1. Rujan 2006.
    Poruka:
    3,072
    Lajkova:
    5,361
    Spol:
    Muškarac
    Interesi:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Grad:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    'Rocket', like all the engines in the Rainhill Trials had two cylinders, one each side. Some very early engines, such as Trevithick's Pen-y-Daren and, I think, Catch-me-who-Can, had a single cylinder but a large wheel attached to the crank which acted both as a flywheel to get the piston over centre but also a means of moving the piston if it were to stop at the end of its stroke.
     
  9. bantamd14

    bantamd14 New Member

    Pridružen(a):
    21. Siječanj 2017.
    Poruka:
    136
    Lajkova:
    92
    Spol:
    Muškarac
    Grad:
    Stafford
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Sorry, silly me, I should have known about Rocket!
     
  10. Jimc

    Jimc Part of the furniture

    Pridružen(a):
    8. Rujan 2005.
    Poruka:
    4,117
    Lajkova:
    4,821
    Interesi:
    Once computers, now part time writer I suppose.
    Grad:
    SE England
    Heritage Railway Volunteer:
    No I do not currently volunteer
    I suppose if we are being pedantic the stroke is the distance forward and back the piston moves over in the course of a wheel revolution, but that is defined by the crank. Most steam engines did have the cylinder centreline aligned to the axle centre, although there were exceptions, notably some of Churchward's standard classes for the GWR. The other point to mention is that the two cranks of a 2 cylinder locomotive are conventionally at 90 degrees to each other, so that when one is dead centre the other is delivering maximum power. An important thing to note is that steam engines are normally double acting, with steam acting on each side of the cylinder alternately, so quite unlike a conventional internal combustion engine.
     
  11. Aberdare

    Aberdare New Member

    Pridružen(a):
    18. Studeni 2016.
    Poruka:
    162
    Lajkova:
    1,550
    Spol:
    Muškarac
    Grad:
    West Somerset
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Steam locomotives, IC engines and shaping machines all use what is called a "Four bar linkage" in their mechanisms. The form of the four bar linkage varies but these are examples of the "Crank-slider" type of the linkage, where one link is infinitely long. For diagrams and simple explanations see:-

    https://en.wikipedia.org/wiki/Four-bar_linkage

    With regards to cylinders that are not on the same centre line as the crank axle, as in selected GWR locomotives, the stroke is greater than twice the crank throw, and one stroke is more than 180 degrees of crank revolution and the other less.

    Four bar linkages can be very complicated in operation and the associated velocity and acceleration diagrams even more so. Shaping machines use the principles to their advantage to have a quick return stroke, so do mechanical hack saws.

    All linked valve gears use multiple four bar linkages.

    Andy.
     
    Steve se sviđa ovo.
  12. nickt

    nickt Member

    Pridružen(a):
    17. Travanj 2009.
    Poruka:
    489
    Lajkova:
    259
    Spol:
    Muškarac
    Which GWR locos didn't have cylinders aligned with driving axle?
     
  13. Jimc

    Jimc Part of the furniture

    Pridružen(a):
    8. Rujan 2005.
    Poruka:
    4,117
    Lajkova:
    4,821
    Interesi:
    Once computers, now part time writer I suppose.
    Grad:
    SE England
    Heritage Railway Volunteer:
    No I do not currently volunteer
    All the original 18x30 cylinder types, but the not the later 4-6-0s and 4-4-0s/4-4-2ts.
     
  14. Steve

    Steve Resident of Nat Pres Friend

    Pridružen(a):
    7. Listopad 2006.
    Poruka:
    12,729
    Lajkova:
    11,847
    Interesi:
    Gentleman of leisure, nowadays
    Grad:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Every day’s a learning day. Not come across this before. No wonder those GW thingies set up a fore and aft motion so easily. :)
     
  15. Flying Phil

    Flying Phil Part of the furniture

    Pridružen(a):
    10. Prosinac 2018.
    Poruka:
    3,018
    Lajkova:
    6,319
    Spol:
    Muškarac
    Grad:
    Leicestershire
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I'm sure we have all learnt a bit more ..... but it would be nice if the OP (SomeWeeb) could show some appreciation....
     
  16. nickt

    nickt Member

    Pridružen(a):
    17. Travanj 2009.
    Poruka:
    489
    Lajkova:
    259
    Spol:
    Muškarac
    How much out of alignment were they, and was it noticeable in operation?
     
  17. LMS2968

    LMS2968 Part of the furniture

    Pridružen(a):
    1. Rujan 2006.
    Poruka:
    3,072
    Lajkova:
    5,361
    Spol:
    Muškarac
    Interesi:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Grad:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I think it was four inches?

    Stanier brought it to the LMS and it was supposed to be applied to the 2-6-0s. In the end, the cylinders were lowered to line up with the coupled wheel centres and this left a big gap between the running plate and top of the valve chests.
     
  18. Jimc

    Jimc Part of the furniture

    Pridružen(a):
    8. Rujan 2005.
    Poruka:
    4,117
    Lajkova:
    4,821
    Interesi:
    Once computers, now part time writer I suppose.
    Grad:
    SE England
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Two and a half inches.
     
    Aberdare se sviđa ovo.
  19. bluetrain

    bluetrain Well-Known Member

    Pridružen(a):
    3. Ožujak 2019.
    Poruka:
    1,561
    Lajkova:
    1,584
    Spol:
    Muškarac
    Grad:
    Wiltshire
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    According to Holcroft, the 2½-in off-set was devised to stop the cylinders fouling the loading gauge on the small-wheeled 28XX engines. A glance at the GWR loading gauge shows the likely source of the difficulty - the step at 1ft 10in above rail level where the width limit reduces from 9ft 0in to 8ft 8in.

    Other British companies more typically addressed similar problems by inclining the cylinders to get them to a higher level and by bringing the cylinders closer together than in GW practice. The extreme example was of course the LMS Hughes "Crab" 2-6-0, an ungainly but very clever design.
     

    Privici:

    • LG-02a.jpg
      LG-02a.jpg
      Veličina datoteke:
      173.9 KB
      Pregleda:
      24
  20. Eightpot

    Eightpot Resident of Nat Pres Friend

    Pridružen(a):
    10. Kolovoz 2006.
    Poruka:
    8,340
    Lajkova:
    2,506
    Spol:
    Muškarac
    Interesi:
    Engineer Emeritus
    Grad:
    Aylesbury
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    The 9F 2-10-0 another example.
     

Podijelite ovu stranicu