If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

Clearing old culverts...

Discussie in 'Civil Engineering M.I.C.' gestart door gwilialan, 5 apr 2016.

  1. gwilialan

    gwilialan Well-Known Member

    Lid geworden:
    8 dec 2012
    Berichten:
    1.716
    Leuk Bevonden:
    4.017
    Geslacht:
    Man
    Locatie:
    Out there somewhere
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    :Arewealone:It looks like this area doesn't get much attention bit hopefully someone can help...

    OK Lads and Lassies, a challenge for you. I need to clear a variety of old culverts that have probably not been cleared for forty years or more while the trackbed was unused. Now we are at the point of clearing the trackside before opening our new extension I keep finding more...:confused:

    The problems I have are:-
    1. Usually only one end access as the outfall is often a 3 metre drop straight into a fast flowing river or onto a very steep embankment.
    2. A mix of stone, iron, concrete and plastic round culverts that may or may not be suitable for jettiing
    3. Some 'built in' stone drains across an embankment about 10 inches wide by 15 inches tall and about 9 yards (8 metres) long set at 15 yard (13m) intervals over a 120 yard (110m) stretch
    4. Often working on proper Brunel embankments with at least a 45 degree slope and bedrock often steeper!
    5. Silt build up ranges from very little (streams) to 28 inches in a 30 inch diameter (blocked ditch:()

    Sizes range from 9 inch to 5 and 6 foot diameters, depths range from just over a metre to about 20 metres on the big embankments and the lengths obviously vary with the depths from about 6 metres to well over 45 metres.

    Bearing in mind the stone lined ones were probably built in about 1850 I am a little cautious about using high powered water jets and any access is forbidden until the condition is fully established which means they have to be cleaned first. Apart from sitting at one end all day 'fishing' with a scraper, hose and extra long drain rods, does anyone have any (sensible) suggestions of how these can be cleared? And does anyone know where I can get different sized scrapers (for the different diameters) to fit 'standard' drain rod threads?

    Incidentally, I know professional video inspections can be expensive but it is surprising what results can be obtained using one of the new 'GoPro' waterproof cameras with video functions fitted to a suitably modified toy remote controlled 4WD pickup with battery and lamp on the back! (Can also be floated on a polystyrene block to inspect culverts with flowing streams! (No not the 4WD, the camera. :Facepalm:) Just make sure everything is firmly fixed on and have a handy length of washing line (oops, sorry, good stout cord) attached to aid retrieval - just in case.:)
     
    gwilialan, 5 apr 2016
    #1
  2. flying scotsman123

    flying scotsman123 Resident of Nat Pres

    Lid geworden:
    9 sep 2013
    Berichten:
    10.718
    Leuk Bevonden:
    18.851
    Geslacht:
    Man
    Locatie:
    Cheltenham
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    flying scotsman123, 5 apr 2016
    #2
  3. huochemi

    huochemi Part of the furniture

    Lid geworden:
    6 mei 2008
    Berichten:
    3.076
    Leuk Bevonden:
    1.551
    Geslacht:
    Man
    Locatie:
    UK
    Heritage Railway Volunteer:
    No I do not currently volunteer
    huochemi, 5 apr 2016
    #3

Deel Deze Pagina