If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

Pink engine?!

Discussion in 'Steam Traction' started by City of truro fan, Nov 12, 2020.

  1. peckett

    peckett Member

    Joined:
    Sep 26, 2006
    Messages:
    726
    Likes Received:
    549
    I think I have spoke about this before ,I had a fusible plug go on a loco with about a 10 square foot grate area ,the fire, quite large ,was out in a mater of minutes.
    Leaking tubes on the rear tube plate ,bottom row were nothing unusable ,we would wait until the weekend before replacing or trying to expand ,if they weren't burnt away to much. If a tube was blowing a fair amount we had (job to describe )a long rod about 3/8 round and four foot or so long,with a plate 5 or 6 ins square welded on one end ,the rod would be shoved up the afending tube ,the plate would divert the steam/water down on to the fire, not towards the fire hole door. Quite often the leaking tubes would seal up when out working.No brick arches were fitted to the locos.
     
    Wenlock likes this.
  2. Big Al

    Big Al Nat Pres stalwart Staff Member Moderator

    Joined:
    May 30, 2009
    Messages:
    21,064
    Likes Received:
    20,773
    Location:
    1016
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Totally logical and has to be size related. The little Andrew Barclay I used to part own had one safety valve - another safety device - but a Merchant Navy has three.
     
  3. Johnb

    Johnb Nat Pres stalwart

    Joined:
    Dec 3, 2014
    Messages:
    14,315
    Likes Received:
    16,391
    Gender:
    Male
    Occupation:
    Retired, best job I've ever had
    Location:
    Buckinghamshire
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    That may open up a whole new discussion. The GWR were happy with just one safety valve, the LNER two but the LMS insisted on four for their Pacifics
     
    Richard Roper and andrewshimmin like this.
  4. clinker

    clinker Member

    Joined:
    Oct 8, 2016
    Messages:
    569
    Likes Received:
    348
    Gender:
    Male
    Location:
    romford
    Heritage Railway Volunteer:
    No I do not currently volunteer
    In My 'Road Steam' life I've seen a fire on a 6 square foot grate literally doused by a plug dropping, just giving the engine enough time to get off of the road.(Into a pub carpark). I'm guessing that Stratfords reluctance to fit fusible plugs probably goes back mto the small boilers used on the Eastern Counties Railway, whereby a dropped plug on Brentwood Bank would put the locomotive out of action, and therefore if singleheading the whole train would have to stop, whereras a scorched crown, provided that it hadn't ruptured MAY get over Ingrave summit and allow the loco to be changed at Shenfield
     
  5. Mr Valentine

    Mr Valentine Member

    Joined:
    Mar 9, 2018
    Messages:
    235
    Likes Received:
    815
    Gender:
    Male
    Location:
    Titfield
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Swindon actually used two valves. I was a bit surprised by the comment (amongst others...) about Barclays only having one, but I guess as there's just a single spring it can be interpreted that way.
     
    Wenlock likes this.
  6. Johnb

    Johnb Nat Pres stalwart

    Joined:
    Dec 3, 2014
    Messages:
    14,315
    Likes Received:
    16,391
    Gender:
    Male
    Occupation:
    Retired, best job I've ever had
    Location:
    Buckinghamshire
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Forgive my ignorance of anything that’s copper capped! I didn’t know that
     
    Richard Roper and Mr Valentine like this.
  7. peckett

    peckett Member

    Joined:
    Sep 26, 2006
    Messages:
    726
    Likes Received:
    549
    Yes ,I worked with four Barclays ,all had two, they were 14 and 16 inc cylinder loco's.
     
    Mr Valentine likes this.
  8. Big Al

    Big Al Nat Pres stalwart Staff Member Moderator

    Joined:
    May 30, 2009
    Messages:
    21,064
    Likes Received:
    20,773
    Location:
    1016
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Yes, as @Mr Valentine says two valves but one spring so I agree it's a matter of how you describe it. I guess my more general point was really to do with having more fusible plugs in large locomotives and similarly for safety valves. With the separate safety valves on a big pacific they might be set to operate progressively at slightly different pressures. And the order in which they were triggered might also be deliberate. So, for example, the valve furthest from the driver and pointing slightly away from him would go first so as to minimise steam obscuring vision and obviously also giving a signal to the fireman as it would be on his side.
     
    jnc likes this.
  9. Hirn

    Hirn Member

    Joined:
    Aug 11, 2015
    Messages:
    462
    Likes Received:
    295
    Gender:
    Male
    I was careful to state "reduces the temperature", it certainly would not put out a deep hot fire. The reaction of steam on hot coal or coke is endothermic, absorbing heat, cooling as in the water gas cycle which used coke to get producer gas - principally carbon monoxide - by passing steam through coke. This was intermittent: first blowing air through the fire to get the coke up to temperature and then steam to get what you wanted until everything had cooled down and the reaction tailed off. In a gas producer fire box one of the effects is that by introducing steam under the grate you lower lower the firebed temperature which gives a considerable effect in mitigating clinkering.

    (Weeping tube ends in the firebox tube plate affect the performance of the boiler surprisingly little - I have known a locomotive give a remarkable performance with something approaching a sheet of water running down under the tubes.)
     
    jnc likes this.
  10. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Back in the day, safety valves were set to the required pressure in the works using the steam from the works boiler and MPD's were not allowed to touch them, only change them. Thus, with individual pop valves, it would be pot luck which valve blew first. Nowadays the heritage movement doesn't have that luxury and valves are nearly always set on the loco, in which case you can choose which valve blows first, although, as the second/third valve should blow at the red line, any valve blowing earlier has got to be below that pressure. Inspectors usually accept an accumulation pressure of 5 psi above the red line, especially with spring balance valves.
    Two valves has been accepted as requirement on steam boilers since the 1850's and was a legal requirement under the Factories Act. The reason for more valves, as found on the larger locomotives, is almost certainly down to standardisation. The railways would have standard valves of a few different sizes and, if you really needed a larger valve, it made sense to fit more of a standard design. Valve height also played a part. The bigger the physical size of the valve, the taller it must be and height becomes critical on the larger locos built to the limits of the loading gauge.
     
  11. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    The 'Stipulations and Conditions' of the Rainhill Trials, 1829, stated:
    "There must be two safety valves, one of which must be completely out of the reach of the Engine man, and neither of which must be fastened down while the Engine is working."

    So it goes back even further than that.
     
  12. andrewshimmin

    andrewshimmin Well-Known Member

    Joined:
    Mar 18, 2011
    Messages:
    1,761
    Likes Received:
    2,160
    Heritage Railway Volunteer:
    No I do not currently volunteer
    "Modern H&S gone mad" etc.

    RPSI, FfRS, TRPS, RERPS, RHDRA, WLLRPC
     
  13. Mr Valentine

    Mr Valentine Member

    Joined:
    Mar 9, 2018
    Messages:
    235
    Likes Received:
    815
    Gender:
    Male
    Location:
    Titfield
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    One oddity I've found is the Wantage tram Shannon. The current boiler, which dates from 1896, only has one valve, and replaced the 1857 original which had two!

    Oh and to spice things up a bit more, it only has one injector.
     

Share This Page