If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

GWR 813 Failure

Discussion in 'Steam Traction' started by nick813, Apr 26, 2022.

  1. 32110

    32110 Member

    Joined:
    May 20, 2006
    Messages:
    627
    Likes Received:
    726
    Gender:
    Male
    Occupation:
    Retired from full time paid work
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Could the casting be welded? There are specialist cast iron welders who might be able to advise.
     
  2. nick813

    nick813 Well-Known Member Loco Owner

    Joined:
    Jan 28, 2010
    Messages:
    1,503
    Likes Received:
    1,503
    Gender:
    Male
    Location:
    poole dorset
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I think it would be not worth while having the casting welded. it is over 100 years old. The Fund is going ahead with a new casting in steel.
     
  3. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Given the work required to get at it, would you trust a repaired item and hope it doesn't break again?
     
  4. Martin Perry

    Martin Perry Nat Pres stalwart Staff Member Moderator Friend

    Joined:
    Apr 15, 2006
    Messages:
    16,510
    Likes Received:
    7,753
    Location:
    1012 / 60158
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Does it need to be a casting? Could it not be fabricated?
     
  5. 30854

    30854 Resident of Nat Pres

    Joined:
    Mar 8, 2017
    Messages:
    12,172
    Likes Received:
    11,493
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Brighton&Hove
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Wondering that myself. I was also wondering about the advisability (necessity?) of replacing 'handed' components in pairs.
     
  6. 8126

    8126 Member

    Joined:
    Mar 17, 2014
    Messages:
    823
    Likes Received:
    962
    Gender:
    Male
    If I'm understanding the earlier posts and pictures correctly, it's a single cast stretcher housing a transverse spring, so is both hands in one, so to speak.

    As for the relative merits of casting and fabrication, while fabrication has its virtues, I'll note that the Beachy Head team recently decided to replace an existing fabricated bogie stretcher with a casting. They needed to change it anyway, but it's clearly not as straightforward as: "Fabrications: cheap, good. Castings: expensive, bad." I think the lack of accessibility of the welds for regular inspection was cited, as well as authenticity.
     
    Last edited: May 23, 2022
    LMS2968, Jamessquared and 30854 like this.
  7. 30854

    30854 Resident of Nat Pres

    Joined:
    Mar 8, 2017
    Messages:
    12,172
    Likes Received:
    11,493
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Brighton&Hove
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Quite a bit to chew on there. Cheers. Can't help but think of 72010's manifold 'spider' casting ....
     
  8. Jamessquared

    Jamessquared Nat Pres stalwart

    Joined:
    Mar 8, 2008
    Messages:
    26,103
    Likes Received:
    57,422
    Location:
    LBSC 215
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    I think one of the things that, ten - fifteen years ago, counted against castings and led various groups to investigate fabrication was the cost of pattern making, particularly when an expensive pattern might be amortised over just a single one-off casting. (And, related, the scarcity of traditional pattern-making skills).

    I think that reason is diminishing. I note in post 20 above that the broken casting has gone for 3D scanning. Take the image produced and it is a relatively small job (for someone with suitable skills!) to turn it into a drawing from which a poly pattern can be machined, all done in ones and zeros. That leads to a marked decrease in cost of casting for one-off components.

    Obviously there are still issues with casting quality, but with a fabricated part you have similar issues with weld quality. So it feels to me that the balance between casting and fabrication for one-off components is possibly swinging back towards casting, relative to where it was twenty years or so ago.

    Tom
     
    2392, Steve, LMS2968 and 1 other person like this.
  9. Dunfanaghy Road

    Dunfanaghy Road Well-Known Member

    Joined:
    Oct 9, 2019
    Messages:
    1,252
    Likes Received:
    1,566
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Alton, Hants
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Attached is a shot of the chassis of the ex-Slough Hudswell Clarke taken when it was on the Mid Hants. You can make out the transverse spring under the cab floor, and the cover plate / inspection hatch / whatever that also showed in pics of 813.
    Pat R4029.JPG
     
    240P15, 30854 and Bluenosejohn like this.
  10. Martin Perry

    Martin Perry Nat Pres stalwart Staff Member Moderator Friend

    Joined:
    Apr 15, 2006
    Messages:
    16,510
    Likes Received:
    7,753
    Location:
    1012 / 60158
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    There are pros and cons of both; the particular branch of heavy engineering that I deal with would go fabricated almost all the time. As regards inspection, a casting will need as much as welding I would have thought.
     
  11. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    For the most part I agree with Tom but I take issue with the suggestion that weld quality might be a problem. That should only be the case if it is done by an iffy welder (like me) and there is enough technology out there to check the welds on completion.
     
  12. 242A1

    242A1 Well-Known Member

    Joined:
    Dec 3, 2006
    Messages:
    1,558
    Likes Received:
    1,299
    Does the liquid metal-pattern interface display signs of instability in the lost foam process? It is a concern when casting aluminium alloys by means of this method.
     
  13. alexl102

    alexl102 Member

    Joined:
    Mar 1, 2019
    Messages:
    448
    Likes Received:
    309
    Gender:
    Male
    Location:
    Leeds
    Heritage Railway Volunteer:
    No I do not currently volunteer
    Presumably this means the loco is out of action for the remainder of the summer at least?
     
  14. 2392

    2392 Well-Known Member

    Joined:
    Jun 7, 2010
    Messages:
    1,902
    Likes Received:
    1,148
    Gender:
    Male
    Location:
    Felling on Tyne
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Reading through just a page or 2 of this thread., makes me think back to the early/mid 1970s'. IIRC the owners of 6201 Princess Elizabeth made quite a splash in the railway media when they retubed the boiler..... Yet today that sort of thing is looked on as almost routine, just like the driver oiling round all the bearings etc. Just look at what folk have got upto in the last fifty [yes nearly fifty] years when it come to replacing even building complete locomotives [i.e. Tornado] or making really quite complicated replacement parts..... without thinking sort of thing.
     
    Last edited: Feb 25, 2023
    clinker likes this.
  15. 8126

    8126 Member

    Joined:
    Mar 17, 2014
    Messages:
    823
    Likes Received:
    962
    Gender:
    Male
    For what it's worth, I've commissioned a few 3D scans, mostly for fabrications where we need the as-welded form. I've never put out a single casting for manufacture.

    The process of scanning and interpreting is increasingly routine; the main trick is in getting a 'watertight' surface that the software can actually recognise as a closed solid. Even then, relatively run of the mill CAD software has got quite good at stitching up surfaces containing gaps where the part was sitting on a support.

    Taking the example of scanning an existing part as a pattern, once you've got that watertight solid, things like scaling up for a shrinkage allowance and adding a machining allowance on the appropriate surfaces are basically trivial with current software.

    Given that 813 had a casting already, it seems to me that in the interests of authenticity, if it's cost (and performance) competitive to produce a new casting, that is more desirable than to replace with a fabrication. Using a stronger steel (or maybe SG iron) casting in place of the original grey iron seems like an acceptable allowance for the original having broken. No, you probably wouldn't do it that way in modern industry, but there's not much modern about 813 either.
     
  16. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    26 May 2022

    [​IMG]

    [​IMG]
     
  17. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    There was a time not so long ago when a piece of three-quarter inch plate across the top and screwed and bolted to the existing casting bits would have put it back in service quite quickly and probably seen it to the end of its working life.
     
    RLinkinS, Bluenosejohn and LMS2968 like this.
  18. Dunfanaghy Road

    Dunfanaghy Road Well-Known Member

    Joined:
    Oct 9, 2019
    Messages:
    1,252
    Likes Received:
    1,566
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Alton, Hants
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    A jury-rig solution is one thing, but surely preservation is something a bit more ambitious?
    Pat
     
  19. clinker

    clinker Member

    Joined:
    Oct 8, 2016
    Messages:
    569
    Likes Received:
    348
    Gender:
    Male
    Location:
    romford
    Heritage Railway Volunteer:
    No I do not currently volunteer





    Two opinions, both 'Worthy' in their own way. One of My engines finished It's working life with a pot mender in the fire box crown, have a guess whether I retained It after restoration?
     
  20. RLinkinS

    RLinkinS Member

    Joined:
    Nov 8, 2008
    Messages:
    912
    Likes Received:
    928
    Gender:
    Male
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    We did similar on nuclear power stations

    Sent from my SM-A105FN using Tapatalk
     
    Steve and weltrol like this.

Share This Page