If you register, you can do a lot more. And become an active part of our growing community. You'll have access to hidden forums, and enjoy the ability of replying and starting conversations.

73096

Discussion in 'Steam Traction' started by domeyhead, Mar 16, 2009.

Thread Status:
Not open for further replies.
  1. dhic001

    dhic001 Member

    Joined:
    Jan 20, 2008
    Messages:
    312
    Likes Received:
    35
    Location:
    New Zealand
    Looking at the pics on the website, you may well be right, if it came out the back side of the piston. Does anyone know?
    Daniel
     
  2. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    In a PM to another poster I put forward the following scenario (pure speculation on my behalf, but a possibility):
    If it was a simple hydraulic explosion then the force on the piston would be evenly distributed and unlikely to buckle the rod to that extent. I'm wondering if there has been a hydraulic lock on the back stroke, which has pushed out the core plug towards the front of the piston. The plug is certainly missing from the 6 o'clock position on the rear side and seemingly in place but damaged on the front side of the piston from the photos published.
    It's similar but not quite the same as your theory. Being much closer to the action than me, I'm sure that you have better access to all the facts. I have only seen the posted photos and video and a 450 mile return trip to look at the evidence isn't really worth thinking about.
    With reference to our previous posts, is this speculating or an interesting discussion? I think that it is the latter and worth carrying on in a sensible manner until the official conclusion is known. Just the Sherlock Holmes in me.
     
  3. std tank

    std tank Part of the furniture

    Joined:
    Sep 20, 2005
    Messages:
    3,808
    Likes Received:
    946
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Liverpool
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    Just adding another question to the puzzle. On most of the photos the bits of the cylinder show fresh clean fractures. That is, except the photo of 17th March which is of the front cylinder cover attached to the cylinder remains and the front draincock. At the lower left of the cylinder remains is a distinct area of red rust on the fracture face. Any opinions on this?
     
  4. Dan Hamblin

    Dan Hamblin Part of the furniture

    Joined:
    Mar 27, 2006
    Messages:
    2,544
    Likes Received:
    181
    Occupation:
    Rolling Stock Engineer
    Location:
    Kent
    I picked up on the back cover going first yesterday:

    It just seems odd to me that the core plug could come loose so quickly and move that far (remember - this is secured with a thread) without some prior warning that it was occurring.

    Regards,

    Dan
     
  5. 73129

    73129 Part of the furniture

    Joined:
    Sep 24, 2007
    Messages:
    4,496
    Likes Received:
    1,079
    Location:
    Winchester
    Hi all does anyone know if owning groups or loco owners have taken there BR standard locos or other LMS locos out of service to check the core plugs in their locos? Or would they wait until their locos require a piston exam?
     
  6. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    As it is a known problem I would hope that loco owners/railways routinely check the core plugs on P & V exams. If not, I would hope that a specific exam has been carried out by now and that it is added to the check list.
     
  7. Fireman Dave

    Fireman Dave New Member

    Joined:
    Oct 13, 2008
    Messages:
    105
    Likes Received:
    5
    I do, believe me. I did however misinterpret your post a bit.
     
  8. Roger

    Roger New Member

    Joined:
    Dec 16, 2005
    Messages:
    173
    Likes Received:
    0
    Occupation:
    coordinater mobile play project
    Location:
    london
    my 2pence worth in the armchair engineers stakes.
    Core plug works loose, loose enough to begin striking cylinder cover leaving witness marks. one each hammer the thread is stripped a little excacerbating the situation. eventualy thread is stripped, this would only reqire plug to come out enough to touch cyl. cover, plus pitch of thread, on power stroke plug is blown out in one go. plug falls to bottom of cylinder and is trapped between piston at end of stroke and rear cylinder cover. rear cylinder cover pushed off pushing it out of alignment causing piston to drop breaking through bottom of cylinder at rearwhich is already damaged by cly. cover being pushed off. on subsequent forward stroke lowered piston takes out rest if cylinder by ploughing through it, requiring considerable force as piston attacks cylinder end on. This results in bending of piston rod. It may have been worth noting where the various parts were found to give an indication of the sequence of events. ~I realise latter may be difficult due to the forces involved scattering debris.
    It may be interesting to note whether the cavity side thread on front of piston is also stripped, it should be .
    rog
     
  9. Penricecastle

    Penricecastle Member

    Joined:
    Jul 23, 2007
    Messages:
    297
    Likes Received:
    136
    Some years ago, I seem to remember a similar thing happening to 7325 the GWR Collett Mogul on the SVR (although not as drastic). I think that was caused by a core plug coming loose. If I'm correct, this problem can also occur on GWR locos.
     
  10. boldford

    boldford Member

    Joined:
    Aug 22, 2005
    Messages:
    435
    Likes Received:
    2
    48773; the 8F resident on the SVR suffered in a similar manner too. Fortunately both engines' cylinders were repairable with "metal locking".
     
  11. 34007

    34007 Part of the furniture

    Joined:
    Mar 16, 2007
    Messages:
    3,166
    Likes Received:
    1
    Gender:
    Male
    Location:
    Hampshire
    A question - Once a new Cylinder has been made for the loco; won't this have to be pressure tested? And ongoing tests after this?
     
  12. buseng

    buseng Part of the furniture

    Joined:
    Sep 9, 2005
    Messages:
    4,799
    Likes Received:
    349
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Tilehurst, Reading, Berks.
    Won't go into details here, but the article on page 15 of the latest issue of Steam Railway(361) makes interesting reading.
     
  13. Dan Hamblin

    Dan Hamblin Part of the furniture

    Joined:
    Mar 27, 2006
    Messages:
    2,544
    Likes Received:
    181
    Occupation:
    Rolling Stock Engineer
    Location:
    Kent
    Yes, seems to suggest that hydraulicing was a contributing cause of the failure.

    Regards,

    Dan
     
  14. cct man

    cct man Part of the furniture

    Joined:
    Jan 15, 2007
    Messages:
    3,220
    Likes Received:
    49
    Occupation:
    CONSTRUCTION
    Location:
    LONDON
    Can someone explain whay hydraulicing id please?.

    Thanks
    Chris
     
  15. OldChap

    OldChap Member

    Joined:
    Apr 29, 2007
    Messages:
    401
    Likes Received:
    150
    Heritage Railway Volunteer:
    No I do not currently volunteer
     
  16. LMS2968

    LMS2968 Part of the furniture

    Joined:
    Sep 1, 2006
    Messages:
    2,987
    Likes Received:
    5,084
    Gender:
    Male
    Occupation:
    Lecturer retired: Archivist of Stanier Mogul Fund
    Location:
    Wigan
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    There are three states of matter:

    1 Solid - definite shape, definite volume
    2 Liquid - indefinite shape, definite volume
    3 Gas - indefinite shape, indefinite volume

    In simple terms, this means that a litre (or gallon) of liquid, such as water, will always occupy that volume - or space - even though it changes its shape. A litre of a gas, such as steam, will expand to fill the available space, or contract as the volume decreases (although with a change of pressure). So if a piston approaches the end of its stroke with steam trapped between it and the cylinder cover, the steam will contract to allow it, albeit with a pressure increase. If though there is water in that space, and once the water has been pushed to fill all the space, any further movement of the piston will try to reduce the volume of the water. This cannot happen, so the space must either expand (blow off the cylinder cover) or the piston must stop. At very slow speeds, the piston might well stop moving once the water is fully distributed within the space and there is nowhere alse for it to go; this is known as 'hydraulicking'.
     
  17. 34007

    34007 Part of the furniture

    Joined:
    Mar 16, 2007
    Messages:
    3,166
    Likes Received:
    1
    Gender:
    Male
    Location:
    Hampshire
    You certainly learn something new every day....
     
  18. Steve

    Steve Resident of Nat Pres Friend

    Joined:
    Oct 7, 2006
    Messages:
    11,930
    Likes Received:
    10,088
    Occupation:
    Gentleman of leisure, nowadays
    Location:
    Near Leeds
    Heritage Railway Volunteer:
    Yes I am an active volunteer
    But if you are aspiring footplate crew it should not be that new! Hydraulicking is one of an engineman's greatest worries.

    There does seem to be an emerging opinion on the ultimate cause of this mishap. Whether it is right, I don't know.
     
  19. ralphchadkirk

    ralphchadkirk New Member Account Suspended

    Joined:
    Jan 3, 2009
    Messages:
    198
    Likes Received:
    0
    It is not. In my various discussions with the "management", it has been confirmed that it did not happen.
     
  20. boldford

    boldford Member

    Joined:
    Aug 22, 2005
    Messages:
    435
    Likes Received:
    2
    The new LH cylinder for 34027 was hydraulically tested before fitting to the frames.
     
Thread Status:
Not open for further replies.

Share This Page